EVPN advertise static ARP entry
Hello, Is there a way to make static ARP entries being advertised over EVPN? I have added an static entry in my BGP EVPN speaker but somehow that entry is not being advertised in the EVPN network. Any help is very welcome. Thanks,
Felipe - FRR expects the neighbor entry to show up in a vxlan bridge in order to know to replicate it. Have you done this? donald On Thu, Jul 12, 2018 at 12:01 PM, Felipe Arturo Polanco <felipeapolanco@gmail.com> wrote:
Hello,
Is there a way to make static ARP entries being advertised over EVPN?
I have added an static entry in my BGP EVPN speaker but somehow that entry is not being advertised in the EVPN network.
Any help is very welcome.
Thanks,
_______________________________________________ frog mailing list frog@lists.frrouting.org https://lists.frrouting.org/listinfo/frog
Hi Donald, I have an L2 working fine right now between two neighbors. As soon as I add a veth interface into the same bridge where the Vxlan interface is connected, that MAC address is advertised to the other neighbor without any problem. Also I see the entry in "bridge fdb show" command to send the broadcasts to the other neighbor using its VTEP IP: 00:00:00:00:00:00 dev vxlan200 dst 198.18.0.12 self permanent 198.18.0.12 is the neighbor IP. I have an L2 network 100.64.0.0/24 One router has 100.64.0.10 in the bridge and the neighbor has 100.64.0.11 in its bridge, they can communicate fine over VxLAN using the information provided by EVPN. I am adding an static entry in the ARP table of 100.64.0.10 but this entry is not being propagated over EVPN # arp -i br100 -s 100.64.0.2 62:e1:e3:18:24:f8 pub The output in EVPN is not reflecting this new ARP entry: # show evpn arp-cache vni 100 Number of ARPs (local and remote) known for this VNI: 3 IP Type MAC Remote VTEP 100.64.0.10 local 62:e1:e3:18:24:f8 fe80::60e1:e3ff:fe18:24f8 local 62:e1:e3:18:24:f8 100.64.0.11 local 22:b9:50:4c:b8:9c And when I check the neighbor to see why it cannot ping this is showing up: # arp -n Address HWtype HWaddress Flags Mask Iface 100.64.0.2 (incomplete) br100 100.64.0.10 ether 62:e1:e3:18:24:f8 C br100 If I manually add ARP entry into the neighbor(100.64.0.11) table it works. Not sure if this answer this question Donald, this is pretty much where I am right now. On Thu, Jul 12, 2018 at 12:07 PM, Donald Sharp <sharpd@cumulusnetworks.com> wrote:
Felipe -
FRR expects the neighbor entry to show up in a vxlan bridge in order to know to replicate it. Have you done this?
donald
On Thu, Jul 12, 2018 at 12:01 PM, Felipe Arturo Polanco <felipeapolanco@gmail.com> wrote:
Hello,
Is there a way to make static ARP entries being advertised over EVPN?
I have added an static entry in my BGP EVPN speaker but somehow that entry is not being advertised in the EVPN network.
Any help is very welcome.
Thanks,
_______________________________________________ frog mailing list frog@lists.frrouting.org https://lists.frrouting.org/listinfo/frog
participants (2)
-
Donald Sharp -
Felipe Arturo Polanco