- frog - lists.frrouting.org

TCP retransmits
by Travis Garrison 31 Dec '19

31 Dec '19

We are getting sporadic speed issues and other weirdness after we installed our 2 new cores running FRR. The routers are HP DL380G8 servers with 64Gb of ram, dual Intel Xeon E5-2690 V2 3GHz 10 core CPUs. We disabled hyperthreading. The nics are Mellanox ConnectX3 Pros 40Gb using the native drivers from Debian 10. All updates and firmware have been applied. We show no errors in the frr.log or messages. We did notice that in a packet capture we are getting a lot of TCP retransmits and TCP out of orders on the internal side. Looks to be about 40 to 50% of our traffic is retransmits. Anyone here have any ideas? We have 2 10Gb internet feeds coming into 2 Mikrotik CRS326-24S+2Q+RM core switches. These switches are then connected with 40Gb DAC cables to the core routers on interface eno1. The switches are not connected together. The 2 core routers also have a 40Gb DAC cable connecting both together on interface eno1d1. Also we have 2 10Gb fiber feeds running to all the edge routers which are Mikrotik RB4011 or CCR1009s that are connected to the core switches. I can draw a diagram out but was unsure if I could attach it to this email or not. The core routers are running an MTU size of 2000 (with the exception of the ISP feed which is running 1500). We have verified that the edge routers and core switches are also running at 2000 MTU. The fiber network supports up to 8096 MTU. ISP1 is giving us full tables while ISP2 is currently giving us a default route only. They will be adding the capability of BGP and full routes in the next month. Through ISP1 we are also joining the local IXC and will be peering with Netflix. Do we need to redistribute the routes between the 2 cores? Core router /etc/network/interfaces auto eno1 iface eno1 inet manual mtu 2000 #ISP auto eno1.4003 iface eno1.4003 inet static address 1x.x.58.114/30 gateway 1x.x.58.113 dns-nameservers x.x.253.138 x.x.2.3 mtu 1500 #RTR auto eno1.3202 iface eno1.3202 inet static address 10.77.129.4/31 #Crossconnect to Core 2 auto eno1d1 iface eno1d1 inet static address 10.77.129.0/31 mtu 2000 #FRR interface eno1.3202 ip ospf network point-to-point ! interface eno1d1 ip ospf cost 1 ip ospf network point-to-point ! router-id 10.77.131.0 ! router bgp 1234 neighbor 10.77.131.1 remote-as 1234 neighbor 10.77.131.1 update-source 10.77.131.0 neighbor 1x.x.58.113 remote-as 4321 neighbor 1x.x.58.113 update-source 1x.x.58.114 ! address-family ipv4 unicast network 10.x.20.0/24 neighbor 10.77.131.5 default-originate route-map GW neighbor 10.77.131.5 prefix-list defaultonly out neighbor 1x.x.58.113 soft-reconfiguration inbound neighbor 1x.x.58.113 prefix-list infilter in neighbor 1x.x.58.113 prefix-list outfilter out exit-address-family ! router ospf ospf router-id 10.77.131.0 passive-interface eno1.4003 network 10.77.129.0/31 area 0.0.0.0 ! ip prefix-list defaultonly seq 100 permit 0.0.0.0/0 ip prefix-list infilter seq 100 permit 0.0.0.0/0 le 24 ip prefix-list infilter seq 6 deny 10.77.128.0/22 le 32 ip prefix-list outfilter seq 5 permit 10.x.20.0/24 le 24 ! route-map GW permit 10 set metric 1 #ip l 2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2000 qdisc mq state UP mode DEFAULT group default qlen 1000 link/ether x:x:1b:80:c4:01 brd ff:ff:ff:ff:ff:ff 3: eno1d1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2000 qdisc mq state UP mode DEFAULT group default qlen 1000 link/ether x:x:1b:80:c4:02 brd ff:ff:ff:ff:ff:ff 5: eno1.4003@eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000 link/ether x:x:1b:80:c4:01 brd ff:ff:ff:ff:ff:ff 8: eno1.3202@eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2000 qdisc noqueue state UP mode DEFAULT group default qlen 1000 link/ether x:x:1b:80:c4:01 brd ff:ff:ff:ff:ff:ff Thanks Travis Garrison

2 1

RES: frog Digest, Vol 33, Issue 18
by Junior Corazza 30 Dec '19

30 Dec '19

Hello Donald, how are you? I understand that it may be a limitation of FRR or some kernels to apply l2vpn mpls, but in this case specifically I would not need FRR to participate in the VPN, the idea is that FRR serves exclusively to be RouteReflector of address-family l2vpn mpls. I will use other routers to effectively make Kompella l2vpn. I know you are an active contributor to the project, do you think this could happen in FRR? Tks ----------------------------------------------- From: Donald Sharp <sharpd(a)cumulusnetworks.com> To: Junior Corazza <corazza(a)telic.com.br> Cc: frog <frog(a)lists.frrouting.org> Subject: Re: [FROG] L2vpn MPLS AFI Message-ID: <CAK989yfbEGDwG6o5f7tKaPrW2CXmwUS+BS0F1n++xTqNE0XQgA(a)mail.gmail.com> Content-Type: text/plain; charset="UTF-8" FRR does not have the capability of doing `l2vpn mpls` at this point in time. I am not aware of anyone publically working on this feature at this point in time. donald On Thu, Dec 26, 2019 at 9:12 PM Junior Corazza <corazza(a)telic.com.br> wrote: > > Hello people. > > I was testing FRR 7.2 to use it as RouteReflecor for l2vpn and l3vpn. > The problem is that there is no address family for l2vpn mpls, there > is only for evpn. > > Can you tell me if it is possible to use RouteReflector for L2vpn Kompella? > I mean, is there this feature? > If not, can you tell me if this is in the roadmap of the project? > > > > > > > _______________________________________________ > frog mailing list > frog(a)lists.frrouting.org > https://lists.frrouting.org/listinfo/frog ------------------------------ Subject: Digest Footer _______________________________________________ frog mailing list frog(a)lists.frrouting.org https://lists.frrouting.org/listinfo/frog ------------------------------ End of frog Digest, Vol 33, Issue 18 ************************************

2 1

L2vpn MPLS AFI
by Junior Corazza 29 Dec '19

29 Dec '19

Hello people. I was testing FRR 7.2 to use it as RouteReflecor for l2vpn and l3vpn. The problem is that there is no address family for l2vpn mpls, there is only for evpn. Can you tell me if it is possible to use RouteReflector for L2vpn Kompella? I mean, is there this feature? If not, can you tell me if this is in the roadmap of the project?

2 1

CISCO OSPF to FRR OSPF conversion
by Antoine DURAND 28 Dec '19

28 Dec '19

2 1

question for those that know
by o1bigtenor 17 Dec '19

17 Dec '19

Greetings It seems that I will be allowed to enter the 'modern' internet world by next fall. By that I mean that we are hopefully going to be able to have a direct individual fiber connection. That means that some things really need updating. One of the bits of stuff I'm looking at is a managed switch. Am finding that some such are built on ONIE which means that I get to start on a Debian platform (goodie - - - I'm already sorta comfortable with that!). What I don't know anything about and am really unsure of is - - - - is FRRouting something that I can use to control run or otherwise use a managed switch? (Am really wanting to use open source software - - - - just quite tired of being for sale on the other side.) Hopefully the question isn't impertinent - - - - I don't know enough about networking to know what to look for and the parts of FRR seem to be the same list that is mentioned for a level 3 switch so - - - - - help? TIA

1 0

FRR-stable DEB for Ubuntu 19.10 (Eoan)
by Volodymyr Litovka 16 Dec '19

16 Dec '19

Dear colleagues, are there any plans on getting FRR-stable package available for Ubuntu 19.10 (Eoan)? There is no this package on deb.frrouting.com and suggestion is to ask on mailing list, while mailing list archives are silent on this. Thank you. -- Volodymyr Litovka "Vision without Execution is Hallucination." -- Thomas Edison

1 0

FW: Failed to start frr.service: Unit frr.service not found
by ian.2.oakley＠bt.com 11 Dec '19

11 Dec '19

Apologies, forgot to CC FROG in this. From: Oakley,I,Ian,TUS2 R Sent: 10 December 2019 16:31 To: Travis Garrison <tgarrison(a)netviscom.com> Subject: RE: [FROG] Failed to start frr.service: Unit frr.service not found Hi Travis, Right. Well, it’s slightly immaterial, as when I go “0 to upgrade, 3 to newly install, 9 to remove and 12 not to upgrade. Need to get 2,748 kB of archives. After this operation, 4,562 kB of additional disk space will be used. Do you want to continue? [Y/n] Y” The process aborts. Which I’m again fairly certain isn’t supposed to happen. Deleting frr.list before the attempt didn’t seem to make a difference. What should I do? Best regards, Ian From: Travis Garrison <tgarrison(a)netviscom.com<mailto:tgarrison@netviscom.com>> Sent: 10 December 2019 16:26 To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> Cc: frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org> Subject: RE: [FROG] Failed to start frr.service: Unit frr.service not found FRR is a replacement for quagga Thanks Travis From: frog <frog-bounces(a)lists.frrouting.org<mailto:frog-bounces@lists.frrouting.org>> On Behalf Of ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com> Sent: Tuesday, December 10, 2019 10:22 AM To: qlyoung(a)cumulusnetworks.com<mailto:qlyoung@cumulusnetworks.com> Cc: frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org> Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not found Hi Quentin, I did as you suggested and it got to this prompt: The following additional packages will be installed: libyang0.16 Suggested packages: frr-doc The following packages will be REMOVED quagga quagga-bgpd quagga-core quagga-isisd quagga-ospf6d quagga-ospfd quagga-pimd quagga-ripd quagga-ripngd The following NEW packages will be installed frr frr-pythontools libyang0.16 I don’t want to have the quagga packages uninstalled. Is there an option to install FRR without uninstalling Quagga? Best regards, Ian From: Quentin Young <qlyoung(a)cumulusnetworks.com<mailto:qlyoung@cumulusnetworks.com>> Sent: 10 December 2019 15:58 To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> Cc: frog <frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org>> Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not found looking at the line again looks like you missed at least some of the instructions. you should be able to just copy paste this whole block from `deb.frrouting.org<http://deb.frrouting.org>` directly into bash though you should make sure to delete /etc/apt/sources.list.d/frr.list before trying the following again ------- # add GPG key curl -s https://deb.frrouting.org/frr/keys.asc | sudo apt-key add - # possible values for FRRVER: frr-6 frr-7 frr-stable # frr-stable will be the latest official stable release FRRVER="frr-stable" echo deb https://deb.frrouting.org/frr $(lsb_release -s -c) $FRRVER | sudo tee -a /etc/apt/sources.list.d/frr.list # update and install FRR sudo apt update && sudo apt install frr frr-pythontools ------ On Tue, Dec 10, 2019, 4:13 AM <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> wrote: Hi Quentin, I did as you suggested and got this: sudo apt update [sudo] password for user: E: Malformed entry 1 in list file /etc/apt/sources.list.d/frr.list (Component) E: The list of sources could not be read. I take that to mean it didn’t work. How should I resolve it? Best regards, Ian From: Quentin Young <qlyoung(a)cumulusnetworks.com<mailto:qlyoung@cumulusnetworks.com>> Sent: 09 December 2019 18:59 To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> Cc: abauvin(a)scaleway.com<mailto:abauvin@scaleway.com>; frog <frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org>> Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not found That means it worked, and you can now perform an `apt update` followed by `apt install frr`. On Mon, Dec 9, 2019 at 12:16 PM <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> wrote: Hi Alexis, Ignore the previous message I sent, I managed to get past that step. However, I'm now stuck on a different step. When I enter the command "echo deb https://deb.frrouting.org/frr $(lsb_release -s -c) $FRRVER | sudo tee -a /etc/apt/sources.list.d/frr.list" I get "deb https://deb.frrouting.org/frr bionic" What does that mean? Best regards, Ian -----Original Message----- From: Alexis Bauvin <abauvin(a)scaleway.com<mailto:abauvin@scaleway.com>> Sent: 09 December 2019 16:30 To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> Cc: sharpd(a)cumulusnetworks.com<mailto:sharpd@cumulusnetworks.com>; frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org> Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not found Hi Ian, Since you’re running Ubuntu, the simplest way to get FRR installed the right way for production (not development) is through the official APT repository holding prepackaged DEB files: https://deb.frrouting.org Regards, Alexis (re-send due to using wrong email address) > Le 9 déc. 2019 à 14:14, <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> a écrit : > > Hi Donald, > > I don't have Slack unfortunately. I assume uninstalling and then reinstalling FRR, but this time in the correct location, would help; however, I can't find in the Installation guide (docs.frrouting.org/en/latest/installation.html<http://docs.frrouting.org/en/latest/installation.html>) where I should install FRR. Where should I install it? > > Best regards, > Ian > > -----Original Message----- > From: Donald Sharp <sharpd(a)cumulusnetworks.com<mailto:sharpd@cumulusnetworks.com>> > Sent: 09 December 2019 13:10 > To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> > Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not > found > > Ian - > > Can you join us in our slack? Goto https://frrouting.org and click on the slack link for a self-invite. I suspect there are more than a few things wrong and it might be a faster way to communicate and work through the issues. > > donald > > On Mon, Dec 9, 2019 at 8:07 AM <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> wrote: >> >> Hi Donald, >> >> The output of journalctl -f, after I copied frr.service into /etc/system/system, is: >> Dec 09 13:00:29 IanRed systemd[16172]: frr.service: Failed at step >> EXEC spawning /usr/lib/frr/frrinit.sh: No such file or directory Dec >> 09 13:00:29 IanRed systemd[1]: frr.service: Control process exited, code=exited status=203 Dec 09 13:00:29 IanRed systemd[1]: frr.service: Failed with result 'exit-code'. >> Dec 09 13:00:29 IanRed systemd[1]: Failed to start FRRouting. >> Dec 09 13:00:29 IanRed systemd[1]: frr.service: Triggering OnFailure= dependencies. >> Dec 09 13:00:29 IanRed systemd[1]: frr.service: Failed to enqueue >> OnFailure= job: No such file or directory Dec 09 13:00:29 IanRed >> sudo[16143]: pam_unix(sudo:session): session closed for user root Dec 09 13:01:30 IanRed systemd[1]: Started Run anacron jobs. >> Dec 09 13:01:30 IanRed anacron[16187]: Anacron 2.3 started on >> 2019-12-09 Dec 09 13:01:30 IanRed anacron[16187]: Normal exit (0 jobs >> run) >> >> I don't have a /etc/frr directory; this I presume is because I installed such that the home directory is located in /home/user/. >> >> Hope that helps. >> >> Best regards, >> Ian >> >> -----Original Message----- >> From: Donald Sharp <sharpd(a)cumulusnetworks.com<mailto:sharpd@cumulusnetworks.com>> >> Sent: 09 December 2019 12:55 >> To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> >> Cc: frog <frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org>> >> Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not >> found >> >> Ian - >> >> What's the contents of your `/etc/frr/daemons` file as well as the output of `journalctl -f` from when you do a systemctl start frr? >> >> donald >> >> On Mon, Dec 9, 2019 at 7:27 AM <ian.2.oakley(a)bt.com<mailto:ian.2.oakley@bt.com>> wrote: >>> >>> Hi, >>> >>> >>> >>> I installed FRR on my Ubuntu virtual machine from source, hoping to use it with CORE for multicast routing with PIM. >>> However, I haven’t been able to manage even that; when I attempt to >>> start the FRR service (sudo service frr start) I am given the error >>> message in the subject (Failed to start frr.service: Unit >>> frr.service not found.) >>> >>> This is despite me running the command in my /frr/tools directory where frr.service is located. >>> >>> Am I missing something here? >>> >>> >>> >>> Best regards, >>> >>> Ian Oakley >>> >>> >>> >>> _______________________________________________ >>> frog mailing list >>> frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org> >>> https://lists.frrouting.org/listinfo/frog > _______________________________________________ > frog mailing list > frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org> > https://lists.frrouting.org/listinfo/frog _______________________________________________ frog mailing list frog(a)lists.frrouting.org<mailto:frog@lists.frrouting.org> https://lists.frrouting.org/listinfo/frog

2 3

Re: [FROG] Failed to start frr.service: Unit frr.service not found
by ian.2.oakley＠bt.com 10 Dec '19

10 Dec '19

Hi Donald, I don't have Slack unfortunately. I assume uninstalling and then reinstalling FRR, but this time in the correct location, would help; however, I can't find in the Installation guide (docs.frrouting.org/en/latest/installation.html) where I should install FRR. Where should I install it? Best regards, Ian -----Original Message----- From: Donald Sharp <sharpd(a)cumulusnetworks.com> Sent: 09 December 2019 13:10 To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com> Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not found Ian - Can you join us in our slack? Goto https://frrouting.org and click on the slack link for a self-invite. I suspect there are more than a few things wrong and it might be a faster way to communicate and work through the issues. donald On Mon, Dec 9, 2019 at 8:07 AM <ian.2.oakley(a)bt.com> wrote: > > Hi Donald, > > The output of journalctl -f, after I copied frr.service into /etc/system/system, is: > Dec 09 13:00:29 IanRed systemd[16172]: frr.service: Failed at step > EXEC spawning /usr/lib/frr/frrinit.sh: No such file or directory Dec > 09 13:00:29 IanRed systemd[1]: frr.service: Control process exited, code=exited status=203 Dec 09 13:00:29 IanRed systemd[1]: frr.service: Failed with result 'exit-code'. > Dec 09 13:00:29 IanRed systemd[1]: Failed to start FRRouting. > Dec 09 13:00:29 IanRed systemd[1]: frr.service: Triggering OnFailure= dependencies. > Dec 09 13:00:29 IanRed systemd[1]: frr.service: Failed to enqueue > OnFailure= job: No such file or directory Dec 09 13:00:29 IanRed > sudo[16143]: pam_unix(sudo:session): session closed for user root Dec 09 13:01:30 IanRed systemd[1]: Started Run anacron jobs. > Dec 09 13:01:30 IanRed anacron[16187]: Anacron 2.3 started on > 2019-12-09 Dec 09 13:01:30 IanRed anacron[16187]: Normal exit (0 jobs > run) > > I don't have a /etc/frr directory; this I presume is because I installed such that the home directory is located in /home/user/. > > Hope that helps. > > Best regards, > Ian > > -----Original Message----- > From: Donald Sharp <sharpd(a)cumulusnetworks.com> > Sent: 09 December 2019 12:55 > To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com> > Cc: frog <frog(a)lists.frrouting.org> > Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not > found > > Ian - > > What's the contents of your `/etc/frr/daemons` file as well as the output of `journalctl -f` from when you do a systemctl start frr? > > donald > > On Mon, Dec 9, 2019 at 7:27 AM <ian.2.oakley(a)bt.com> wrote: > > > > Hi, > > > > > > > > I installed FRR on my Ubuntu virtual machine from source, hoping to use it with CORE for multicast routing with PIM. > > However, I haven’t been able to manage even that; when I attempt to > > start the FRR service (sudo service frr start) I am given the error > > message in the subject (Failed to start frr.service: Unit > > frr.service not found.) > > > > This is despite me running the command in my /frr/tools directory where frr.service is located. > > > > Am I missing something here? > > > > > > > > Best regards, > > > > Ian Oakley > > > > > > > > _______________________________________________ > > frog mailing list > > frog(a)lists.frrouting.org > > https://lists.frrouting.org/listinfo/frog

6 10

insert RIP routes into specified table (Linux)
by frr user 10 Dec '19

10 Dec '19

Hello to all. I am trying to use frr 6.0.2 on Debian 10.2; Show, plz, the simplest example of how to insert a route accepted by the RIP protocol into the specified table? For example, the route 192.0.2.0/24 received via RIP needs to be inserted into table #250. Or tell me, do I need to use VRF for this? Thanks.

1 0

Re: [FROG] Failed to start frr.service: Unit frr.service not found
by Alexis Bauvin 09 Dec '19

09 Dec '19

Hi, Yup, that’s why. The systemd service file is not dynamic and does not take into account the actual install path. You may be able to use systemd to run frr as your user, in your home, by modifying the paths in the service file. However, that is not really what this service file is meant for. Depending on how you configured your frr build, just changing the various paths of the service might be enough. frrinit.sh might give you some trouble though, as this script is rather huge and convoluted. Good luck! Alexis PS: don’t forget the ML in your CCs ;) > Le 9 déc. 2019 à 14:05, <ian.2.oakley(a)bt.com> <ian.2.oakley(a)bt.com> a écrit : > > Hi Alexis, > > I copied the frr.service file into /etc/system/system and then ran sudo service frr start. > That gave me the following: > Job for frr.service failed because the control process exited with error code. > See "systemctl status frr.service" and "journalctl -xe" for details. > > Running systemctl status frr.service gave me: > frr.service - FRRouting > Loaded: loaded (/etc/systemd/system/frr.service; disabled; vendor preset: enabled) > Active: failed (Result: exit-code) since Mon 2019-12-09 13:00:29 GMT; 11s ago > Docs: https://frrouting.readthedocs.io/en/latest/setup.html > Process: 16172 ExecStart=/usr/lib/frr/frrinit.sh start (code=exited, status=203/EXEC) > > Dec 09 13:00:29 IanRed systemd[1]: Starting FRRouting... > Dec 09 13:00:29 IanRed systemd[16172]: frr.service: Failed to execute command: No such file or directory > Dec 09 13:00:29 IanRed systemd[16172]: frr.service: Failed at step EXEC spawning /usr/lib/frr/frrinit.sh: No such file or directory > Dec 09 13:00:29 IanRed systemd[1]: frr.service: Control process exited, code=exited status=203 > Dec 09 13:00:29 IanRed systemd[1]: frr.service: Failed with result 'exit-code'. > Dec 09 13:00:29 IanRed systemd[1]: Failed to start FRRouting. > Dec 09 13:00:29 IanRed systemd[1]: frr.service: Triggering OnFailure= dependencies. > Dec 09 13:00:29 IanRed systemd[1]: frr.service: Failed to enqueue OnFailure= job: No such file or directory > > The install directory for my FRR install is in /home/user/ - does that explain anything? > > Regards, > Ian > > -----Original Message----- > From: Alexis Bauvin <abauvin(a)scaleway.com> > Sent: 09 December 2019 12:55 > To: Oakley,I,Ian,TUS2 R <ian.2.oakley(a)bt.com> > Cc: frog(a)lists.frrouting.org > Subject: Re: [FROG] Failed to start frr.service: Unit frr.service not found > > Hi, > > This is a SystemD unit file. It needs to be placed in /etc/systemd/system for systemd to find it and start frr. > > Alexis > >> Le 9 déc. 2019 à 13:07, <ian.2.oakley(a)bt.com> <ian.2.oakley(a)bt.com> a écrit : >> >> Hi, >> >> I installed FRR on my Ubuntu virtual machine from source, hoping to use it with CORE for multicast routing with PIM. >> However, I haven’t been able to manage even that; when I attempt to >> start the FRR service (sudo service frr start) I am given the error >> message in the subject (Failed to start frr.service: Unit frr.service not found.) This is despite me running the command in my /frr/tools directory where frr.service is located. >> Am I missing something here? >> >> Best regards, >> Ian Oakley >> >> _______________________________________________ >> frog mailing list >> frog(a)lists.frrouting.org >> https://lists.frrouting.org/listinfo/frog >

1 0